How to Choose a Channel Letter Bender
A good channel letter bender fits four things: the letter styles you sell, the materials you use, the volume you run, and the shop you have. Price matters, but it comes after those four.
This guide takes them in order, then covers support, total cost, and payment. If you already know your letter styles, the quick pick below points you to a machine.
Quick pick by letter style
| If you build | Look at |
|---|---|
| Trimless letters and reverse halo without welding | Ascent 4AS. It also makes side-lit letters with plastic returns. |
| The same, plus F-trim letters | Ascent 5AS. Choose it when you also need F-trim. |
| Traditional trim-cap letters | Ascent EDGE-3 or EDGE-4. The EDGE-4 adds 8-axis servo feeding and punches weep and rivet holes. |
| Your own aluminum or plastic trim | Ascent TMB-3. It makes trim from aluminum coil, handles plastic trim, and bends flanged returns. |
| Large letters, deep returns, or thick aluminum | Ascent MAX-V2. Returns up to 15.7 in tall, and aluminum up to 0.125 in thick. |
Not sure yet? Try the machine selection wizard, or call us and we will go through your work with you.
1. Start with the letter styles you sell
List the styles you build now, and the ones customers ask for. They decide which machine fits.
- Trim-cap letters have flanged returns with a trim cap on the face. Benders that notch and flange (EDGE-3, EDGE-4, and TMB-3) do this work.
- Traditional reverse halo has returns welded to a back. Every Ascent bender can bend the returns for it.
- Trimless letters and reverse halo without welding use Ascent extrusion. The face is held in a groove, and the letter is assembled with a pneumatic nail gun and stainless clips, so there is no adhesive table. The 4AS and 5AS bend returns from this extrusion. Read true trimless compared with adhesive-bonded systems for the difference.
- F-trim letters need the 5AS.
- Oversized letters and cabinets need the MAX-V2.
A machine that makes only trim-cap letters limits you if customers start asking for trimless. A trimless machine is more than you need if you never sell it. Choose for the styles you expect to sell over the next few years, not only for last year's mix.
2. Check the size and material limits
Compare the limits that stop a job: the height of the return, and the thickness and type of metal.
| Machine | Return height | Aluminum thickness | Stainless steel thickness |
|---|---|---|---|
| 4AS and 5AS | Up to 8 in | 0.040 and 0.063 in | Yes, up to 0.040 in |
| EDGE-3 | Up to 8 in | 0.040 and 0.063 in; 0.080 in for bending only | Yes, up to 0.040 in |
| EDGE-4 | Up to 8 in | 0.040 and 0.063 in | Yes, up to 0.040 in |
| TMB-3 | Up to 8 in | 0.040 and 0.063 in | No |
| MAX-V2 | Up to 15.7 in | Up to 0.080 in at full height; 0.125 in up to 8 in tall | Yes, up to 0.055 in (also galvanized) |
Letter height is a separate limit. The 4AS and 5AS make letters from 3 in tall, and the EDGE-3 from 5 in, both with no upper limit. Check your smallest letters first.
3. Match the machine to your volume
As a general range, an Ascent bender produces returns for about 100 to 300 individual letters in a typical eight-hour shift. Large, simple letters go faster. Small letters and detailed logos take longer.
Before you pay for speed, look at the rest of the line. Welding, LED installation, and stapling usually set the pace in a letter shop, and the bender's cycle time is short compared with them. Count the letters you build in a normal week and in your busiest week, then check that the work after bending can keep up.
One trained operator runs a bender for a full shift. Once a job is loaded, feeding, bending, and cutting are automated, and the operator handles material changes and quality checks.
4. Look at the software and the files
Ask what file types the machine accepts, whether the software is included, and what it takes to add a new material. Ascent benders accept DXF and AI files directly, so your design files go to the machine without a separate prep program. The control software is included in the price and runs on a Windows interface. Material setups are pre-programmed, so changing materials needs no hardware changes, and software updates are free.
5. Check what the machine needs from your shop
A bender needs power, compressed air, and floor space. Get the numbers before you buy and have an electrician look at them.
- Power: the 4AS, 5AS, EDGE-3, EDGE-4, and TMB-3 run on 120 V, 30 A. The MAX-V2 is rated 220 V, 3.75 kW.
- Compressed air: the benders run on compressed air, and a compressor is not included in the price, so plan for one. The 4AS uses compressed air instead of an oil pump, and the EDGE-4 clamps pneumatically at 43 to 116 PSI.
- Floor space: leave room around the machine to load coil and take finished returns away. Ask us about the footprint of the model you are considering.
Installation at your shop is part of the price. An Ascent technician installs the machine and trains your operators on site.
6. Compare support, not only specs
A bender is a production tool. When it stops, your shop slows down. Ask every supplier these questions:
- Who installs it, and where? Ascent installs and trains at your shop. Installation and training typically take three days.
- How are my operators trained? New operators are usually productive within a few days, and training covers final letter assembly.
- What does the warranty cover? Ascent benders carry up to three years of warranty: two years of parts and labor, plus a third year of parts.
- What happens after the warranty ends? Remote diagnostics stay on the machine for its lifetime, and software updates are free. See remote support and training.
- Where are the technicians? Ascent has technicians in Buffalo, Toronto, and Mount Sterling, Kentucky.
7. Compare the full cost
Machine prices only compare when they include the same things. Ask each supplier to put these in writing: shipping and crating, installation at your shop, training days, warranty length and what it covers, software and updates, support after the warranty, and the options you need for the letter styles you want.
The Ascent price of $38,000 to $46,000, depending on the model, includes shipping, on-site installation, operator training, the warranty, software updates, and lifetime remote support. The channel letter bending machine price page lists the price of each model and everything the price covers.
With the 4AS and 5AS, Ascent also includes a starter set: extrusion, clips, and a pneumatic nail gun with 6 mm (0.24 in) pins. You can use it for production or for training. The TMB-3 comes with an aluminum coil for making trim. After that, compare what a letter costs to build: coil, extrusion, trim, and clips. The Materials page lists what Ascent supplies.
8. Plan how you will pay for it
Many shops finance a bender. With Ascent, the customer chooses the lender, and Ascent takes no commission from lenders. Lenders can finance the machine, shipping, and other costs, and payment schedules are flexible. See financing and purchasing compared with financing.
In the US, equipment may qualify for a Section 179 tax deduction in the year it is placed in service. Ask your accountant, and read equipment write-offs for sign shops.
For payback, divide the machine price by the labor you expect to save each month. The channel letter cost calculators work from your own production numbers.
9. One machine or two
If you sell both trimless and trim-cap letters, you may want two machines: a 4AS for trimless and reverse halo (a 5AS if you also run F-trim), plus an EDGE-3 or a TMB-3 for trim-cap letters. Four bending machines compared with one all-in-one goes through the options.
See a machine run before you decide
Ask for a live demo by video call, and bring your letter styles and material list. Call 1-800-927-5107 ext. 1008 or 647-494-7800 ext. 1008, or request a quote.